Leaderboard

Sprint Moto X & any Moto G Flashed to Reliance CDMA FINAL Photo Tutorial Updated:- 08/04/2014 New Method Works 100% Follow easy to use , Modified Photo Tutorial http://www.slideshare.net/hambarde/moto-g-ver3final _________________________________________________________________________________________________ Tested on Verizon and confirmed to be working on Boost model. 1) First we need working wifi connection on phone 2) Then an APK from this link >> http://www.mediafire.com/download/i038c12rrdcbtlj/SPCUtility.apk 3) Allow this MSL app to use WiFi, 4) It gives you SPC, [Works on Verizon and Boost both] [Also works with sprint Moto X] 5) for boost Moto G and Sprint Moto X ##diag# works, but dose not work for Verizon. 6) For verizon Diag , Turn off mobile, remove usb cable, and Press both vol key + power button. 7) As soon as you leave these keys , one menu will pop-up. 8) use vol down keys to select BP Tools then connect use cable. 9) then press vol up . Phone will boot normally with DIAG turn ON. 10) for Boost ##diag# require SPC, which you will get it by SPC apk. 11) now PC will search for drivers (even latest moto driver pack dont have drivers for this) 12) attaching drivers for moto g DIAG. (install it manually) 64Bit Drivers | 32Bit Drivers 13) Use DFS, send SPC. and Put phone in Offline-A mode 14) then you need to change phone and min number to any 1234567890 to change PRL 15) till that time PRL wont change, 16) From DFS you can write AKey. 17) But for data need to use DUMP file, 18) you can use CW nv item write and write DATA DUMP, use free NV Item writer from CW http://www.cdma-ware.com/workshop/nv-items/NV-items_reader_writer.rar (get CW3.6 Dump after registration) here also need to put phone in Offline-A mode before writing DUMP to phone 19) after writing all above, go to DFS and change Min and MDN to ZERO so you will be ready for activation (*228). 20) As you always do - Hit Like UPDATE :- If phone is on 4.3, then you should first update to 4.4.2 then do above steps, other wise you need to redo data settings and might have to flash PRL again. Here are official drivers from Motorola http://www.mymotocast.com/download/MDM?platform=windows I have not tested it but hope this works. These official driver dont work, use above 32bit or 64bit drivers Update : 19/03/2014 1)32bit Drivers mention in point no -12 are tested on WinXP 32bit and on Win7 32bit 2) 64bit Drivers are tested on Win7 & 8 64bit. 3) After factory reset, Min and akey stays as it is, But need to re-configure DATA and PRL. 4) One Click update to 4.4. for boost works perfectly from fastboot mode. Link [and it takes only 10min to update from 4.3 to 4.4.2] 5) Need to reconfigure PRL and DATA after one Click update [same as updating on Wifi] Update 25/03/2014 Photo tutorial [Drivers and Sending SPC] LINK removed, use link on top Update 08-04-2014 (use link on top) Photo tutorial [ Till voice and sms configuration] Data config will be updated sooooon...... LINK removed, use link on top Update :- 14apr14 Getting many msg about not finding software for using tutorial so here are all the software required Dfs demo http://cdmatool.com/downloadFiles/application/Setup%20DFS%2014.03.26.0.zip Nv writer 3.6 http://www.cdma-ware.com/workshop/nv-items/NV-items_reader_writer.rar Spc apk http://www.mediafire.com/download/i038c12rrdcbtlj/SPCUtility.apk 32bit drivers moto g & x https://www.mediafire.com/?ic25458youq1xd9 64 bit drivers https://www.dropbox.com/s/ucr03xx6esqtcdc/DroidX_Diag_x64.rar Moto G MTP Drivers For Win XP SP3 [Modded by Me] https://www.dropbox.com/s/37hpk21lc26h78i/wpdmtp.inf Sent by Moto G on Reliance CDMA DroidX_Diag_x64.rar

On Moto G do not try *#*#33666633*#*# Phone will reboot to DEMO mode and you wont be able to do anything, on every reboot all data will be lost as its in DEMO mode. to get out of DEMO mode, need to do wipe from stock recovery !! So stay away from demo code !! For bypassing initial activation screen just press home key or recent app key, phone will skip activation !

^^^ Thanks for making it new thread, I was going to new post thread but then though of continuing the old one, But you are the best judge !! Thanks again !

Talked to a PPOBOX rep today.. 1) You cannot order more than two phones per person per day.. 2) Both phones must be in different packing.. Two phones in one package is not allowed.. 3) Duty paid will be on current market value for used phones.. (When I asked how they decided market value the guy said google for current market value of your phone you will get it) Also talked to an Ishop rep Ishopinternational is refusing to ship used phones.. Only phones with condition New or New(Other) can be shipped through Ishop.. Talks are going on with customs dept. for the duty applicable for used phones after which they will start shipping used phones (will take a month or so)..

Strictly speaking not from indian brands but Gionee has launched it for india market. Massive 4200 mAh battery Android! Gionee M2 StandBy Time 555Hrs, Talk time 24hrs (3G) / 31.5Hrs (2G) 1.3Ghz Quad Core, Android 4.2.2 5" Display, 1GB RAM, 4GB Internal, Micro SD upto 32GB Dual SIM, dual standby Primary Camera 8.0 MP, LED flash, Secondary 2.0 MP 3G, Bluetooth v4.0, FM Radio, WLAN Direct, USB Internet (Sharing Windows PC internet via USB cable), Gionee Xender, wireless input device(Keyboard & Mouse) Rs 10,850 >> http://www.ebay.in/itm/Gionee-M2-Mobile-Phone-4200-mAh-Battery-1-3GHz-QuadCore-Proc-4-2-2-Jelly-Bean-/261399484717?pt=IN_Mobile_Phones&hash=item3cdc9f992d&_uhb=1#ht_4471wt_1035

There is not a single thread which gives all the information regarding the LS980. also i was getting lot of pm's regarding the GSM unlock. so basically this thread will have all the information, if anything is left out please feel free so message me or in thread. Phone Config LG-G2-LS980 Phone Drivers LS980 Drivers My Experience Personally i was a Samsung fan until they came out with the Kn0x security. i had 2 choice the Note 3 and the LG G2, since the Note 3 had issues with data not working on CDMA mode and the G2 was and still is wallet friendly, so i decided to go with the G2 and till date i DO NOT regret it. LAG is something that is simply not in its dictionary, super smooth. Like the HTC One this phone is also sealed and comes in 2 variants 16 and 32 Gigs. Initially only 2 colors Black and White, now the actual(international) site has many different ones. This one is a LCD compared to the S4 with AMOLED, To be frank only if you have the two phones together you might see the difference. I found the G2 to be more vibrant and a lil brighter side compared to the S4. 1000 times more accurate smartstay display than the S4, Same with auto brightness. Feels much lighter than the S4 and the build quality is anyday better than S4, feels solid in hand. Many have debated about the volume and power keys being at the back, actually its something you have to try and then understand, now if i handle any other phone than my G2 i tend to Tap the display 2 times softly to get the screen going, like the home or power button, im so used to it now. Tap 2 times on display to lock the screen & same to to light the display back again. Initially when i first got the phone i used to tap hard thinking that was the right way and 7/10 times it used to work, did not know that one has to tap very lightly as possible. Soft tap 2 times gets it locked and vice-versa 10/10 times. Its actually easier to use volume rockers in the center position then one side like anyother phone. Theres more to this phone and i dont have the patience nor time to explain everything. Phone definitely requires a case to protect it from fall, i have the Spigen Slim Armour. Runs on 4.2.2JB and 2 updates have been released till date. LS980ZV7 (Initial Release) LS980ZV8 (Security Update) LS980ZVA (Sprint Spark and loki-killer) Not used in India so i have not taken it. LS980ZVC (KitKat 4.4.2 OS Update) Also if you are a custom ROM freak DO NOT INSTALL the ZVA update as it removes the ability to do that. People who have taken it do not worry as there is a work around. Custom ROM installation for people who have taken ZVA update. Only if you understand everything mentioned in the above link proceed else you just might end up with a hard brick. Sprint Dialer Codes Source 5689#*980# - LG Hidden Service Menu Thanks to EricDabbs ##RTN# - RTN Menu ##SCRTN# - Erases any info that has been OTA provisioned. Forces a reboot and re-activation. ##DIAG# - Enables diag mode. this menu blocked by MSL. Simply enter your MSL ##DATA# - Advanced data menu. ##DEBUG# - Debug Menu ##CLEAR# - Reset network settings ##UPDATE# - Forces Activation ##GPSCLRX# - Clear GPS ##GPSTESTPRL# - ?? ##WLAN# - WLAN info ##LOG# - syslog info ##MRU# - MRU Clear ##SSDRTN# - Reset SSD ##TEST - Data Test menu ##YOUROWNMSLHERE# - Service Programming menu ##443336772# Shows MSL code near the bottom of the screen thanks mojo4321 ##4433386368# - Developer menu ##4437736368# - Producer menu How to back up EFS Its already confirmed RUIM data only works if used before flashing anything to the phone, Out of the box phone can be used for RUIM with calls sms and data. so its very important to back up complete stock state EFS partition Two ways to backup EFS, below i have mentioned how to root, during the root process at one stage EFS partition is backed up auto. Or after root use FreeGee from Google Play (Requires root access) Install and backup EFS. How to get you MSL/SPC Easiest method to get SPC: Dial ##443336772# and your SPC/MSL will be displayed on the screen! Probably this will work for other LG phones also. [Credit goes to phonegeek] How to Gain Root Access Root FIle Works with All Baseband Updated ioroot.zip where did i get this ? SOURCE 1 After you have downloaded the file required for root, Put the phone in Debug mode, for this under settings go to Developer Options. If you do not have Developer Options under settings simple go to Settings/About Phone/Software Information under this tab on Build Number 10 times continuously and it will enable the Developer Options in your phone. 2 Under display settings set the screen timeout to 5 minutes(you can set it back to your liking later when you are done with root) 3 Connect your phone to PC/Laptop 4 Under pull down notification change the USB settings from MTP to Charge Only 5 Unzip the ioroot file and from the folder execute the run.bat file 6 The command prompt will ask you to press any key as show in pic below 7 You will be prompted to toggle USB connection shown marked in red, three ways you can toggle that, show in marked yellow, select the first one, remove usb connection from the phone and re-plug it back. the PRESS ENTER. 8 Your phone will show toggled notification and also it will ask you to allow USB Debugging with the computer showing the computers RSA key, Mark "Always allow from this computer" & select ok. The command prompt it will warn you again about loosing warranty and more warnings, this is the last point to decide to continue or press CTRL+C to cancel. PRESS ENTER. Your phone EFS will be backed up like shown in pic below and again it will ask you to press enter, PRESS ENTER. 9 Phone is rooted and phone will reboot. check if you have SuperSu or SU in your phone. How to Unroot Access Superuser app, go to settings of the app & look for Full unroot. Select it and wait for the phone to reboot. Recovery for KitKat 4.4.2 LS980ZVC SOURCE GSM Unlock For G2 LS980 This is a temporary GSM unlock & not a permanent or a solid one. Two known issues, you cant access Wi-Fi settings, as it crashes if you try to access, and you cant dial any number without adding 0 before it. Example: Sunny Leons phone number is 6969696969, to call her you gotta dial 06969696969. If you dial direct 6969696969 the phone app crashes and your phone switches to GSM mode if you are in CDMA mode. As far as i know these are only 2 known bugs this unlock has. hope we get a more stable unlock. Install ROM Toolbox Lite 1 Run Rom Toolbox Lite and select performance marked in red 2 Select build.prop editor marked in red 3 Select search using the magnifying glass icon below marked in red 4 In search field type "build.target" as shown in pic below 5 Select "ro.build,target_operator" as show in pic below 6 Change value from "SPR" to "spr" as show in pic below and press ok marked in yellow. 7 Reboot popup will come, select ok and reboot the phone. Your phone should be GSM unlocked now. Install HIAPN or Tweakker for APN settings of your service provider. Install Telinfo to switch between CDMA(CDMA Auto PRL) & GSM(GSM Auto PRL) Permanent Unlock for the LG-G2-LS980

Requirements 1 Stock LG G2 LS980 Firmware 2 LG Flash Tool 3 Dll file for LG G2 LS980 (LGLS980_20130904_LGFLASHv151.dll) 4 MegaLock.dll All the above can be found on zip file here LG G2 LS980 Drivers Once the required files are downloaded and unzipped, install the LG Flash Tool to default C:\LG\LGFlashTool\ Then unzip the MegaLock.dll.zip file and place the MegaLock.dll file in same directory (C:\LG\LGFlashTool\) Very Important Connect your phone to Pc/Laptop Under Pull Down notification of your phone change the USB settings From MTP to Charge Only Under Device Manager of your Pc/Laptop, Right click on Ports(COM & LPT) as show below in red and select properties in yellow. Select Port Settings as show below Select Advanced as show below Select COM Port Number marked in red and choose COM41 marked in yellow as shown below. It should look like as shown below in red Unplug your phone from Pc/Laptop, switch it of. Put the phone in DOWNLOAD mode by pressing and holding VOL UP key and plug in the USB cable, If you see download mode on phone, give it 5 secs and unplug the USB cable from the phone. Phone has to be in DOWNLOAD mode even after unplugging the USB cable. Run LG Flash Tool & select manual mode marked in red as shown below in pic Once you have selected Manual mode, we have to choose the dll related to LS980, select browse as shown in pic below. Choose the dll file as shown in pic below, This dll file should be found in the main unzipped folder. After choosing the dll file now we have to add the firmware which needs to be flashed. so select "add" shown in red in pic below. Now select the firmware file with the extension *.tot (LS980ZV7_1.tot in our case) as shown in pic below. Once both the dll and the firmware are select choose ok as show in pic below. Now press the yellow arrow mark marked in red as shown in pic below. When you select the yellow arrow, you might get a popup saying "MilkyWay Control Port Open FAIL" just select ok as shown below in pic. Wait for it !!!!! IF YOU GET THE ABOVE PIC !!! its time to connect your phone. Its very important for your phone to be in CHARGE ONLY mode. This you have done earlier in the beginning. Simple connect your phone and wait for the tool to get connected and the flash process to start. Roughly it should take 2 to 3 minutes to flash. The phone will reboot when its still in flash process at around 85% or more. Thats it your phone is fully flashed to complete stock, since its a full flash wait for the phone to boot as if its booting first time. WAIT FOR IT. UNPLUG and enjoy your phone. Feel free to ask questions before proceeding.

Boost Moto G only for Rs 6939.66 (Rs 7,462) http://geb.ebay.in/I...oost-Mobile-NEW use 7% discount coupons from reliance

<< New Topic created, Split from Motorola Announces Moto G >> ------------------------------------------------------------------------------------ Awesome! Will Thank Hitesh in Motorola Language for sharing! Exceptional Phone, Exceptional Price & Above all exceptional helping / sharing Member!

Reliance EVDO is one the finest than any service provider I have seen in my area, gsm or cdma. Sanjay ji's issue is definitely area based. My wife had a DAPO number and had issue with data recently when she shifted to Verizon Note 2. It was solved by Hetal and now has same 2~2.5Mbps speeds round the clock.

As per the discussion on another forum, you could do an online activation and in the last step before payment it would show the SPC it seems. Another user mentioned that the SPCUtility app works -- http://www.mediafire.com/download/i038c12rrdcbtlj/SPCUtility.apk I haven't tried any of these though as my Boost Moto G is still in transit. how much did Boost Moto G cost you ? Boost MOTO G 8gb version, approx 8k on GEB @Genius Danyavad Daaktar babu !!

Very good and useful app for parents to monitor babies. Read description of the app for more details. https://play.google.com/store/apps/details?id=com.sleekbit.dormi They are offering 80% launch discount, use code BEGINNERSTECH Sent from my LG-LS980 using Tapatalk

Pls highlight method to backup n restore efs... That would make the thread complete Sent from my VS980 4G using Tapatalk

If the phone is used on RUIM mode out of the box, data works. Even after the GSM Unlock the data on RUIM will work. Data will not work only if we flash NV, if NV is flashed data on RUIM will stop working and it will start to work on NV mode. IT'S VERY IMPORTANT TO BACK UP EFS BEFORE DOING ANYTHING TO THE PHONE, THIS MESSAGE IS ALSO TO ALL DEALERS. If the dealers provide copy of the EFS in the phone, it would simply be great because the phone will be able to get data on all modes. Like phonegeek mentioned in earlier posts that the EFS can not be restored to its stock state if modified. OP is updated with how to backup EFS.

Note nahi pahuche honge na... Note milte hi permission mil jayegi Sent from my VS980 4G using Tapatalk

I got this from XDA some time back .. dont have the link

If u have locked bootloader, non rooted, system and both radio on same version and stock recovery then onlyy update will be successful on ota Otherwise it will fail! tapatalking.....

For those struggling to get data via RUIM... One of my friend .. keegenohp [ name alphabets reversed to hide identity] was having same issue ... he had programmed phone initially via NV mode and everything was working ...but no data on RUIM But this sunday afternoon .. both of us were bored and had nothing to do .. so began investigating that what have we done different that data is working on mine and not his on RUIM.. and suddenly I Had What Alcoholics Refer to as a 'Moment of Clarity' On my G2 i didnt do any change and just changed the NV mode to RUIM only ... keegenohp on the other hand, had already done NV changes along with data dump akey etc and was later trying by changing to RUIM only mode... keegenohp being a smart guy he is ... had an original EFS backup of the phone [before he did any finger in it that is] ... So he restored it back and voilà!... Data started working on RUIM along with Call and Text of course.. So here is the path for all those Neo`s struggling to find the access code to Xion mainframe. PS1 : Sorry for long reply mods ... contents for the reply can be CRUD ... and freely distriburted under GNU GPL PS2: Sunday afternoons !

Oh ! I hope the change wont take place