Leaderboard

Got this tip from saharsh Mittal To remove Hands Free Activation only need to rename two files in system/ SprintOMADM2.apk. To sprintOMADM2.apk.bak And /system/sprintOMADM2.odbx to sprintODADM2.odbx.apk For this you can use rom tool box root browser or any root file explorer. Below screen shots are from rom tool box (root browser ) Open rom tool box and click on root browser Then open system folder Then open priv-app folder Then scroll down till you see sprintOMADM2. Apk Long press sprintOMADM2. Apk, one menu will pop-up, select rename from it. Then just rename sprintOMADM2. Apk to sprintOMADM2. Apk.bak To Now do same to sprintOMADM2. Odbx, rename it to SprintOMADM2.odbx.bak Now after doing above you you should see file names as below Now just reboot the phone and Hands Free Activation is gone ! And also home key works ! In my last mod I was able to get rid of HFA , but after that Home key was not functioning, in this mod everything works as normal . Now time to get rid of BootLoader unlock warning at every boot ! For this we need to put phone in bootloader mode. And flash this logo.bin file https://www.dropbox.com/s/1d608mqzpykg6ho/logo.bin Command to flash is Fastboot flash logo logo.bin It won't take more then 30sec to do this in bootloader mode. After this just reboot the phone and see the clean booting animation without bootloader warning. Now you have a clean phone ! Enjoy !! Sent by Moto G on Reliance CDMA

this solution is to fix the proximity sensor which goes bad sometimes and even after the call the screen stays black until the person on line cuts the phone or if you press the power button this happens due to dirt and dust accumulating over sensor. so to check if your sensor is working properly do the below test to check sensor dial *#0*# and select sensors(tested on note 2,s4,note 3) when u put your hand on proximity sensor screen turns green with vibration and when u lift your hand it turns back to white but if it doesnt turn white after removing hand that means the sensor has a problem so we lower the value at which the sensor responds note :-you need to be rooted to follow this procedure open cmd and change to your adb folder and type the following command adb shell (you will get a notification on your phone screen accept it) su (give root privilege in phone) echo 0 > /sys/devices/virtual/sensors/proximity_sensor/prox_cal echo 1 > /sys/devices/virtual/sensors/proximity_sensor/prox_cal NOW cat state # put your finger on the sensor and check the value (my came 255) now remove your finger from sensor (it came 51) cat state # This returned 255 #finger on the sensor and 51 #blank value and then do cat /sys/devices/virtual/sensors/proximity_sensor/prox_cal this returned 0,60 45.....so my offset was 0. Ths sum of offset and #blank value was 0 + 51 = 51 that is equal to 33 in HEX. so i increased to 55 and hex value 37 then echo -en $'\x37' > /efs/prox_cal the value 37 will change according to your phone do the above math chown system:system /efs/prox_cal chmod 644 /efs/prox_cal sync reboot now the sensor is working you can check again by dialing *#0*# and do the test again

99% of people know how to change mode from NV to RUIM using DFS, This is for the rest 1% who don't know. Download DFS and install on PC. Phone Drivers I'm using a LG G2 LS980 Sprint CDMA model, so illustrating for the said model Know your SPL/MSL code: Dial ##443336772# Shows MSL code near the bottom of the screen, write it or memorize it. Put the phone into DIAG mode: Dial ##3424#, Enter SPC/MSL code and press ok. Select enable and press ok. Your phone is in DIAG mode. Enable Debug in Developer Options of the phone. If you do not have Developer Options under settings simple go to Settings/About Phone/Software Information under this tap on Build Number 10 times continuously and it will enable the Developer Options in your phone. Put the phone in Charge only Now that your phone is connected, Run DFS on PC & Select Ports marked in red. Select LGE AndroidNet USB Serial Port (COM16) -> this can be any number, its 16 in my case. Once the above port is selected it should it indicate like shown in pic below marked in red. Double click on LGE AndroidNet USB Serial Port (COM16) marked in yellow. If properly connected, it should look like its shown in red in the pic below. Enter your SPC/MSL in the SPC field marked in yellow and then press the SPC button. It should say Device Unlocked in the log window of DFS shown below marked in orange. Now select programming marked in blue and then select read in config marked in red. Select the Ruim Config marked in yellow, change it from NV_ONLY to RUIM_ONLY. Once the mode is changed from NV_ONLY to RUIM_ONLY as shown below marked in red, select write marked in yellow & finally select Reset at top right corner of DFS marked in pink. Your phone should reboot and if your phone is capable of taking a RUIM SIM, all features like voice sms and data should work at this time. I try to make my tutorials as noob friendly as possible, if you still have doubts or confused, don't hesitate to ask.

Don't worry... On sept-oct 2014, they will definitely give some NEWS to Media about, this is going to change everything, sharing tower with Electricity Board, e-governance with e-bribe, e-wiping the bull, signing MoU with Maesapatoemia for under sea cable, Free WiFi on road-side dhaaba, selling data for as cheap as Rs20 per KiloGram, laying OFC on railway track, cheap 4G Lte tablet as well as tonic, testing 4G on 14th floor of Antilia or Uncilia, Phone numbers + PAN numbers alloted for RJio service, etc... But NO 4G LTE service... Then people will say that, RJio will launch on December in memory of his Dad, and hence 2014 will also be skipped... Well, the ex-AirHell executives are doing their job well (like they have done in RCom). 4G Lte will never be launched without kicking them out, imho...

You can format your Nokia C1-00 device by typing: * + 3 + call + Power on. Before the device is reset, you need to provide the lock code. The default lock code is 12345. If it is not working try this code: You can format your device by typing *#7370# in standby mode. Before the device is reset, you need to provide the lock code. The default lock code is 12345. Got this from hard-reset.com Sent by Moto G on Reliance CDMA

You can transfer RCDMA No. from Sim-to-sim or sim-to-nonsim or vice-versa using HCC(handset change card) HCC's are still working,easiest way to transfer your no without visiting RWW.... PM me for HCC

Best part is: "96% of 638 users found this review helpful" !

Read this funny review of s5 on flipkart.. I'm sure they will delete it.. So posting jpg Disclaimer : bad language used... With all sorts of Indian bad words... Open at your own risk... ... Sent from my VS980 4G using Tapatalk