Leaderboard

I have Boost mobile MOTO E LTE XT1526. Everything works on 5.0.2, voice, data, messaging, hotspot, both for CDMA (Tata, MTS, Reliance) and GSM. 5.1 update is downloaded and sitting. Not updated yet. Want to know IF I should go ahead and do it or not. Will it hamper CDMA services in anyway, DATA especially. Thanks

One of the best plan till date offered in GSM postpaid With Freepaid plans a postpaid customer: # Can treat any local and STD reliance number as CUG - all local and std onnet calls are free # Can make unlimited CUG calls even when roaming - on net calls are free even from roaming # Can treat his office (and home) landline numbers as intercom - all landline calls are free # Can treat Office and home calls as intercom even when roaming - all landline calls are free even from roaming # Can receive unlimited incoming calls from any number while in roaming - all roaming incoming calls are free # Gets 900 offnet (Local / STD / Roaming OG) minute - 900 minutes offnet means all reasonable offnet usage will get covered in free minutes Data as per the above plan & Circle taken. TEF_395_445_BH_DL_KOL_OR_RJ_WB.pdf

Requirements 1 Stock LG G2 LS980 Firmware 2 LG Flash Tool 3 Dll file for LG G2 LS980 (LGLS980_20130904_LGFLASHv151.dll) 4 MegaLock.dll All the above can be found on zip file here LG G2 LS980 Drivers Once the required files are downloaded and unzipped, install the LG Flash Tool to default C:\LG\LGFlashTool\ Then unzip the MegaLock.dll.zip file and place the MegaLock.dll file in same directory (C:\LG\LGFlashTool\) Very Important Connect your phone to Pc/Laptop Under Pull Down notification of your phone change the USB settings From MTP to Charge Only Under Device Manager of your Pc/Laptop, Right click on Ports(COM & LPT) as show below in red and select properties in yellow. Select Port Settings as show below Select Advanced as show below Select COM Port Number marked in red and choose COM41 marked in yellow as shown below. It should look like as shown below in red Unplug your phone from Pc/Laptop, switch it of. Put the phone in DOWNLOAD mode by pressing and holding VOL UP key and plug in the USB cable, If you see download mode on phone, give it 5 secs and unplug the USB cable from the phone. Phone has to be in DOWNLOAD mode even after unplugging the USB cable. Run LG Flash Tool & select manual mode marked in red as shown below in pic Once you have selected Manual mode, we have to choose the dll related to LS980, select browse as shown in pic below. Choose the dll file as shown in pic below, This dll file should be found in the main unzipped folder. After choosing the dll file now we have to add the firmware which needs to be flashed. so select "add" shown in red in pic below. Now select the firmware file with the extension *.tot (LS980ZV7_1.tot in our case) as shown in pic below. Once both the dll and the firmware are select choose ok as show in pic below. Now press the yellow arrow mark marked in red as shown in pic below. When you select the yellow arrow, you might get a popup saying "MilkyWay Control Port Open FAIL" just select ok as shown below in pic. Wait for it !!!!! IF YOU GET THE ABOVE PIC !!! its time to connect your phone. Its very important for your phone to be in CHARGE ONLY mode. This you have done earlier in the beginning. Simple connect your phone and wait for the tool to get connected and the flash process to start. Roughly it should take 2 to 3 minutes to flash. The phone will reboot when its still in flash process at around 85% or more. Thats it your phone is fully flashed to complete stock, since its a full flash wait for the phone to boot as if its booting first time. WAIT FOR IT. UNPLUG and enjoy your phone. Feel free to ask questions before proceeding.