manojjha

1. login as root cat /etc/wvdial.conf [Dialer Defaults] Modem = /dev/ttyS3 Baud = 57600 SetVolume = 0 Dial-AT-OK ATDT Command = Init1 = ATZ FlowControl = Hardware (CRTSCTS) Phone = #777 Username = xxxxxxxxxx Password = xxxxxxxxxx New PPPD = yes Carrier Check = no Stupid Mode = 1 2. create a file "reliance" with entry as show below: cat reliance setserial /dev/ttyS3 baud_base 230400 wvdial 3. run "reliance" from root 4. The /var/log/message will show ========= Jun 11 19:45:42 manoj-pc pppd[4788]: pppd 2.4.2 started by root, uid 0 Jun 11 19:45:42 manoj-pc kernel: PPP generic driver version 2.4.2 Jun 11 19:45:42 manoj-pc pppd[4788]: Using interface ppp0 Jun 11 19:45:42 manoj-pc pppd[4788]: Connect: ppp0 <--> /dev/ttyS3 Jun 11 19:45:47 manoj-pc pppd[4788]: PAP authentication succeeded Jun 11 19:45:47 manoj-pc kernel: PPP Deflate Compression module registered Jun 11 19:45:47 manoj-pc pppd[4788]: local IP address 220.224.54.139 Jun 11 19:45:47 manoj-pc pppd[4788]: remote IP address 220.224.134.110 Jun 11 19:45:47 manoj-pc pppd[4788]: primary DNS address 202.138.97.193 Jun 11 19:45:47 manoj-pc pppd[4788]: secondary DNS address 202.138.96.2 5. Once u get the local,remote ip and dns. Add dns address in /etc/resolv.conf cat /etc/resolv.conf nameserver 202.138.103.100 nameserver 202.138.96.2 6. nslookup gmail.com [root@manoj-pc ~]# nslookup gmail.com Server: 202.138.96.2 Address: 202.138.96.2#53 Non-authoritative answer: Name: gmail.com Address: 64.233.161.83 Name: gmail.com Address: 64.233.171.83 Name: gmail.com Address: 72.14.253.83 Enjoy Surfing net with ZTE-MC315 datacrd on Linux. I have tested, this technique on RHEL4AS,and Ubunto. And on both os was itt was working good. Some time while running "reliace" , it not get ip in first run... so you may have to run it again and again, till u get connected. Make sure that u have setserial rpm installed. Manoj Kumar Jha mailid: manoj.jha@oracle.com

1. login as root cat /etc/wvdial.conf [Dialer Defaults] Modem = /dev/ttyS3 Baud = 57600 SetVolume = 0 Dial-AT-OK ATDT Command = Init1 = ATZ FlowControl = Hardware (CRTSCTS) Phone = #777 Username = xxxxxxxxxx Password = xxxxxxxxxx New PPPD = yes Carrier Check = no Stupid Mode = 1 2. create a file "reliance" with entry as show below: cat reliance setserial /dev/ttyS3 baud_base 230400 wvdial 3. run "reliance" from root 4. The /var/log/message will show ========= Jun 11 19:45:42 manoj-pc pppd[4788]: pppd 2.4.2 started by root, uid 0 Jun 11 19:45:42 manoj-pc kernel: PPP generic driver version 2.4.2 Jun 11 19:45:42 manoj-pc pppd[4788]: Using interface ppp0 Jun 11 19:45:42 manoj-pc pppd[4788]: Connect: ppp0 <--> /dev/ttyS3 Jun 11 19:45:47 manoj-pc pppd[4788]: PAP authentication succeeded Jun 11 19:45:47 manoj-pc kernel: PPP Deflate Compression module registered Jun 11 19:45:47 manoj-pc pppd[4788]: local IP address 220.224.54.139 Jun 11 19:45:47 manoj-pc pppd[4788]: remote IP address 220.224.134.110 Jun 11 19:45:47 manoj-pc pppd[4788]: primary DNS address 202.138.97.193 Jun 11 19:45:47 manoj-pc pppd[4788]: secondary DNS address 202.138.96.2 5. Once u get the local,remote ip and dns. Add dns address in /etc/resolv.conf cat /etc/resolv.conf nameserver 202.138.103.100 nameserver 202.138.96.2 6. nslookup gmail.com [root@manoj-pc ~]# nslookup gmail.com Server: 202.138.96.2 Address: 202.138.96.2#53 Non-authoritative answer: Name: gmail.com Address: 64.233.161.83 Name: gmail.com Address: 64.233.171.83 Name: gmail.com Address: 72.14.253.83 Enjoy Surfing net with ZTE-MC315 datacrd on Linux. I have tested, this technique on RHEL4AS,and Ubunto. And on both os was itt was working good. Some time while running "reliace" , it not get ip in first run... so you may have to run it again and again, till u get connected. Make sure that u have setserial rpm installed. Manoj Kumar Jha

Hi Any one using reliance "ZTE MC315" datacard on Linux? I am not able to configure it on RHELAS4. Same card is working ok on my WinXP os.

Hi Rohit, I have ZTE-mc315 datacard and when i insert this card to PCMCIA slot it detected on ttys3 on RHEL AS4. But I am not able to configure modem and access internet. The same card is working good on winxp. Please can u help. Manoj