Vinod Nayak 443 Report post Posted February 15, 2014 (edited) Requirements 1 Stock LG G2 LS980 Firmware 2 LG Flash Tool 3 Dll file for LG G2 LS980 (LGLS980_20130904_LGFLASHv151.dll) 4 MegaLock.dll All the above can be found on zip file here LG G2 LS980 Drivers Once the required files are downloaded and unzipped, install the LG Flash Tool to default C:\LG\LGFlashTool\ Then unzip the MegaLock.dll.zip file and place the MegaLock.dll file in same directory (C:\LG\LGFlashTool\) Very Important Connect your phone to Pc/Laptop Under Pull Down notification of your phone change the USB settings From MTP to Charge Only Under Device Manager of your Pc/Laptop, Right click on Ports(COM & LPT) as show below in red and select properties in yellow. Select Port Settings as show below Select Advanced as show below Select COM Port Number marked in red and choose COM41 marked in yellow as shown below. It should look like as shown below in red Unplug your phone from Pc/Laptop, switch it of. Put the phone in DOWNLOAD mode by pressing and holding VOL UP key and plug in the USB cable, If you see download mode on phone, give it 5 secs and unplug the USB cable from the phone. Phone has to be in DOWNLOAD mode even after unplugging the USB cable. Run LG Flash Tool & select manual mode marked in red as shown below in pic Once you have selected Manual mode, we have to choose the dll related to LS980, select browse as shown in pic below. Choose the dll file as shown in pic below, This dll file should be found in the main unzipped folder. After choosing the dll file now we have to add the firmware which needs to be flashed. so select "add" shown in red in pic below. Now select the firmware file with the extension *.tot (LS980ZV7_1.tot in our case) as shown in pic below. Once both the dll and the firmware are select choose ok as show in pic below. Now press the yellow arrow mark marked in red as shown in pic below. When you select the yellow arrow, you might get a popup saying "MilkyWay Control Port Open FAIL" just select ok as shown below in pic. Wait for it !!!!! IF YOU GET THE ABOVE PIC !!! its time to connect your phone. Its very important for your phone to be in CHARGE ONLY mode. This you have done earlier in the beginning. Simple connect your phone and wait for the tool to get connected and the flash process to start. Roughly it should take 2 to 3 minutes to flash. The phone will reboot when its still in flash process at around 85% or more. Thats it your phone is fully flashed to complete stock, since its a full flash wait for the phone to boot as if its booting first time. WAIT FOR IT. UNPLUG and enjoy your phone. Feel free to ask questions before proceeding. Edited February 23, 2014 by Vinod Nayak 15 Share this post Link to post Share on other sites
Vinod Nayak 443 Report post Posted February 15, 2014 (edited) FIX for people who have installed TWRP and stuck after OTA update Source If you see TWRP everytime you boot after OTA update, Follow the code below. VERY IMPORTANT: CODES HAVE TO BE TYPED EXACTLY AS SHOWN WITH SPACES & PUNCTUATION, ONE SMALL MISTAKE CAN GIVE YOU A HARD UNRECOVERABLE BRICK. You should have ADB access, connect phone and use this command. Code: adb shell dd if=/dev/block/platform/msm_sdcc.1/by-name/fota of=/sdcard/fota-backup.img dd if=/dev/zero of=/dev/block/platform/msm_sdcc.1/by-name/fota After all the code is sent, use TWRP menu to reboot the phone. or use adb reboot command. If you dont have ADB, then use TWRP terminal command and follo the code below. Code: dd if=/dev/zero of=/dev/block/platform/msm_sdcc.1/by-name/fota Reboot Edited February 23, 2014 by Vinod Nayak 3 Share this post Link to post Share on other sites
solarisx21 17 Report post Posted February 16, 2014 @ People doing this.....before doing this please make sure your EFS is safely backed up. Because if you lose it during any flashing process - your phone will be rendered a useless brick with no way of going back. Share this post Link to post Share on other sites
gauravjc 47 Report post Posted February 21, 2014 Vinod ji, I'm on ZVA version looking to downgrade using this method but phone is not being detected by LG Flash Tool... windows 7 cannot locate CDC Serial drivers.... pls help .. thx Share this post Link to post Share on other sites
Vinod Nayak 443 Report post Posted February 21, 2014 See if you're drivers are installed properly or not. Sent from my LG-LS980 using Tapatalk Share this post Link to post Share on other sites
solarisx21 17 Report post Posted February 21, 2014 @gauravjc make sure you downgrade the radio first before downgrading the rom...else you can end up with a brick. Share this post Link to post Share on other sites
gauravjc 47 Report post Posted February 21, 2014 Thanks solarisx21 ... how do u downgrade the radio can u pls help ?? Share this post Link to post Share on other sites
solarisx21 17 Report post Posted February 21, 2014 Download the ZV8 radio (from xda autoprime post) flash radio first, then downgrade rom. Let me know if you cannot find the radio...will post link. 1 Share this post Link to post Share on other sites
gauravjc 47 Report post Posted February 22, 2014 Thanks got it .... Share this post Link to post Share on other sites
UbaidullahQadir 0 Report post Posted February 25, 2014 Vinod bhai I've read other posts of downgrading to stock but its written there you have to change the date of the LG flash fool and disconnect the internet and stuff, do I have to do the same thing before starting the process? Share this post Link to post Share on other sites
UbaidullahQadir 0 Report post Posted February 25, 2014 I'm trying to do this my I dont see LGE something under ports, its showing RIM virtual serial See if you're drivers are installed properly or not.Sent from my LG-LS980 using Tapatalk when Im trying to install drivers, it says BASE SYSTEM DEVICE drivers not found Share this post Link to post Share on other sites
Vinod Nayak 443 Report post Posted February 26, 2014 Vinod bhai I've read other posts of downgrading to stock but its written there you have to change the date of the LG flash fool and disconnect the internet and stuff, do I have to do the same thing before starting the process? That's the old method. This is the easier way. Here no need to change date or disconnect internet. Please read the OP. Sent from my LG-LS980 using Tapatalk Share this post Link to post Share on other sites
Vinod Nayak 443 Report post Posted February 26, 2014 hi, as far as i know, u cannot download ringtones from the internet into LG 2030 ... u're stuck with the ones on R world. all u can do with the cabe is surf the web using your phone as a modem ... nothing more !! You need to enable diag mode ##3424# enter SPC and enable select on enable. Sent from my LG-LS980 using Tapatalk Share this post Link to post Share on other sites
UbaidullahQadir 0 Report post Posted March 1, 2014 i unplugged the phone when it was still at 94%, it wasn't going any further. LG flash said download fail does that mean im in trouble now? or it was done already? my phone is fine though Share this post Link to post Share on other sites
Vinod Nayak 443 Report post Posted March 1, 2014 i unplugged the phone when it was still at 94%, it wasn't going any further. LG flash said download fail does that mean im in trouble now? or it was done already? my phone is fine though That's a bug in the flash tool. It never goes to 100%, at one time it says rebooting 120 secs, that's around 85%, at that time phone reboots, you can unplug it. Your phone is complete stock now. Sent from my LG-LS980 using Tapatalk Share this post Link to post Share on other sites
st_7 138 Report post Posted March 1, 2014 ^^^ Yes it is fine once the phone reboots. You don't need to worry about what LG Flash Tool is saying once your phone boots successfully. Share this post Link to post Share on other sites
UbaidullahQadir 0 Report post Posted March 1, 2014 Download the ZV8 radio (from xda autoprime post) flash radio first, then downgrade rom. Let me know if you cannot find the radio...will post link. Hi, my g2 (Sprint) got updated to LS980ZVB (4.4.2). I want to downgrade or root, what could be the solution? Thanks. Share this post Link to post Share on other sites
UbaidullahQadir 0 Report post Posted March 1, 2014 i unplugged the phone when it was still at 94%, it wasn't going any further. LG flash said download fail does that mean im in trouble now? or it was done already? my phone is fine though That's a bug in the flash tool. It never goes to 100%, at one time it says rebooting 120 secs, that's around 85%, at that time phone reboots, you can unplug it. Your phone is complete stock now. Sent from my LG-LS980 using Tapatalk ok thanks for the help, and what is the other problem that you have mentioned about the TWRP? Am i gonna have that issue if i have not installed TWRP? Share this post Link to post Share on other sites
ev1lb0ygen1us 27 Report post Posted March 1, 2014 Download the ZV8 radio (from xda autoprime post) flash radio first, then downgrade rom. Let me know if you cannot find the radio...will post link. Hi, my g2 (Sprint) got updated to LS980ZVB (4.4.2). I want to downgrade or root, what could be the solution? Thanks. Sprint released 4.4.2 ROM update for G2? Or is it just the firmware update? Share this post Link to post Share on other sites
UbaidullahQadir 0 Report post Posted March 2, 2014 Download the ZV8 radio (from xda autoprime post) flash radio first, then downgrade rom. Let me know if you cannot find the radio...will post link. Hi, my g2 (Sprint) got updated to LS980ZVB (4.4.2). I want to downgrade or root, what could be the solution? Thanks. Sprint released 4.4.2 ROM update for G2? Or is it just the firmware update? My android version updated to 4.4.2 and software version updated to LS980ZVB. I thinks sprint is testing Kitkat on G2, its not a final version. Do you have any solution to root or downgrade this version? Share this post Link to post Share on other sites
solarisx21 17 Report post Posted March 2, 2014 ^Why do you take updates without understanding what it is ? First read up about the update on XDA and then take it.....will avoid a lot of headache. Share this post Link to post Share on other sites
drmadhu 87 Report post Posted March 2, 2014 @solarisx21 if u not have solution. Kindly not give answered. But not give this type of answers. Sent from my XT907 Share this post Link to post Share on other sites
Vinod Nayak 443 Report post Posted March 2, 2014 i unplugged the phone when it was still at 94%, it wasn't going any further. LG flash said download fail does that mean im in trouble now? or it was done already? my phone is fine though That's a bug in the flash tool. It never goes to 100%, at one time it says rebooting 120 secs, that's around 85%, at that time phone reboots, you can unplug it. Your phone is complete stock now.Sent from my LG-LS980 using Tapatalk ok thanks for the help, and what is the other problem that you have mentioned about the TWRP? Am i gonna have that issue if i have not installed TWRP?That's if you have updated the phone with TWRP recovery. Many get stuck on TWRP mode, phone gets a bootloop on TWRP. Only for that. Good that you got the 4.4.x update. Where are you located? Don't downgrade. For now stay with that update Sent from my LG-LS980 using Tapatalk Share this post Link to post Share on other sites
solarisx21 17 Report post Posted March 2, 2014 @vijaymalhotra - Its not a question of whether I have a solution or not.....if you do things without understanding the process, you could end up with a bricked device. This is for your own good.... Eg: taking a update on a custom recovery, doing a flash without esn backup... - leads to a brick. Why go through the trouble of unbricking steps, when it can be completely avoided in the first place. Whats the harm in reading up a little ? Share this post Link to post Share on other sites
J Rafael Bakeo Miranda M 0 Report post Posted March 8, 2014 Hey i have a situation, mi laptop doesn't show PORT LCP??? just usb port Share this post Link to post Share on other sites