::Hitesh:: 1,763 Report post Posted October 28, 2015 Root is simple if you are already unlocked your bootloader. Even in 5.1 same root method works. I am yet to flash 5.1 stock , so cannot comment on tethering. But same 5.0.2 method should work Sent from my XT1031 using Tapatalk Share this post Link to post Share on other sites
rishisuri 16 Report post Posted October 28, 2015 Were you rooted before applying the OTA or you unrooted the stock rom? If you were unrooted were you able obtain root after update? no i had unrooted stock rom, and yes i just had to flash recovery and install SU and i got the root Root is simple if you are already unlocked your bootloader. Even in 5.1 same root method works. I am yet to flash 5.1 stock , so cannot comment on tethering. But same 5.0.2 method should work Sent from my XT1031 using Tapatalk the option of tethering is missing from the settings itself , so tethering either by usb, bluetooth or hot spot. Share this post Link to post Share on other sites
iamrafic 85 Report post Posted October 28, 2015 I'm on Stock. If i install the OTA, do i need to re-configure the DATA and PRL settings again? Share this post Link to post Share on other sites
rishisuri 16 Report post Posted October 28, 2015 I'm on Stock. If i install the OTA, do i need to re-configure the DATA and PRL settings again? i might have to flash the prl again.... Share this post Link to post Share on other sites
sangalaviral 6 Report post Posted October 29, 2015 Few problems: 1. Tethering is gone. 2. in DFS PRL Reliance_ID00005_IS683C.prl not present instead Reliance_ID00051_IS683C.prl is present. Configured using this calls and data work. 3. Home country is set to USA after programming. Before prl programming it was India. 4. Network displayed as chameleon. Share this post Link to post Share on other sites
rishisuri 16 Report post Posted October 29, 2015 Few problems: 1. Tethering is gone. 2. in DFS PRL Reliance_ID00005_IS683C.prl not present instead Reliance_ID00051_IS683C.prl is present. Configured using this calls and data work. 3. Home country is set to USA after programming. Before prl programming it was India. 4. Network displayed as chameleon. i suppose no.1 is the problem and remaining 3 does not make any difference if data, sms and call are working.... 1 Share this post Link to post Share on other sites
sangalaviral 6 Report post Posted October 30, 2015 Point 3 is problem as well. Whenever there is a +91 it converts it to 011 91. So its a headache. Share this post Link to post Share on other sites
rishisuri 16 Report post Posted October 31, 2015 Point 3 is problem as well. Whenever there is a +91 it converts it to 011 91. So its a headache. i think you can switch off assisted dialing and there will be no problem and before doing that change the reference country to india. Share this post Link to post Share on other sites
rishisuri 16 Report post Posted October 31, 2015 Point 3 is problem as well. Whenever there is a +91 it converts it to 011 91. So its a headache. as it is +91 does not work on reliance, so always enter a number in the phone book with prefix '0' Share this post Link to post Share on other sites
sangalaviral 6 Report post Posted October 31, 2015 I don't use just 1 phone and I do travel abroad. So its not an option Share this post Link to post Share on other sites
Ravi Padia 0 Report post Posted November 10, 2015 dear hitebhai mistakenly i have updated my moto g to 5.1 by OTA i had mange to got back the network but i m unable to call and receive i went to reliance web they told me your handset is not active but when i dial228 its shows activated please help me thanks Share this post Link to post Share on other sites
loypalm 9 Report post Posted November 10, 2015 I too got the OTA update but after doing the update have lost calls and data. I did the programming once again and now on *228, I get " your phone is already registered" but when trying to make calls, it automatically gets cut. If I try to call the number form another phone, I get "switched Off" message. I think A-Key is not getting written in DFS any solution? Share this post Link to post Share on other sites
omitav 2 Report post Posted November 10, 2015 (edited) hi gurus, need some help with my cdma MotoG that was programmed from Boost and in to Reliance. Everything was working fine, but suddenly all outgoing SMS have stopped. every message i send fails. Would anyone know what setting needs to be fixed please? Any help is highly appreciated :-) Thanks in advance Omi Edited November 10, 2015 by rajanmehta << Topic Merged >> Share this post Link to post Share on other sites
loypalm 9 Report post Posted November 11, 2015 It could also be MIN error I suppose. Is there any way to reprovision the phone over OTA by RCDMA? Share this post Link to post Share on other sites
omitav 2 Report post Posted November 12, 2015 It could also be MIN error I suppose. Is there any way to reprovision the phone over OTA by RCDMA? hmmm. but if it was a MIN error then incoming calls would also have stopped working. But calls are working fine. OTA reprovisioning seems to be have been stopped recently - when i try *228, nowadays I get the message that 'the phone has already been activated'. I think I need to check the settings with DFS, but not sure which settings would be the right one to fix :-( Share this post Link to post Share on other sites
shade29n 0 Report post Posted December 12, 2015 Hey guys you can flash lollipop 5.1 From here http://forum.xda-developers.com/moto-g/development/rom-stock-motorola-lollipop-rom-t3017510 Sent from my XT1031 using Tapatalk Share this post Link to post Share on other sites
shade29n 0 Report post Posted December 12, 2015 After flashing stock lollipop 5.1, you can activate tethering using app WiFi tether router, you don't lose data and signal after this upgrade http://forum.xda-developers.com/moto-g/development/rom-stock-motorola-lollipop-rom-t3017510 Sent from my XT1031 using Tapatalk Share this post Link to post Share on other sites
